Ads for marauder .25

Degassing tool.. Is there another way/tool?

This area is dedicated to the .25 caliber Benjamin Marauder by Crosman.

Degassing tool.. Is there another way/tool?

Postby LSS152 » Sun Dec 17, 2017 8:54 am

Guys I am getting ready to do a few modifications to my MRod. I do not have the degas tool. Is there another tool that will work or can I use the dry fire method with out messing anything up? I have put in a order for the tool but it may be after Christmas before I get it. Thanks for the help!
LSS152
 
Posts: 18
Joined: Mon Jan 02, 2017 8:59 am

Re: Degassing tool.. Is there another way/tool?

Postby PB_Matrix » Sun Dec 17, 2017 9:39 am

A few techniques:

Loosen the gauge slowly till it leaks a bit, once the air stops, loosen it about a 1/4 turn till it leaks bit again, repeat till the gauge reads zero

If you have a pump, pump the rifle up, just enough so that the fill valve opens, then slowly unscrew the vent valve so that both the pump and rifle vent. Might take a few tries to get all the air out.

or just dry fire it till empty, no big deal..
PB_Matrix
 
Posts: 244
Joined: Thu Mar 20, 2014 4:23 am

Re: Degassing tool.. Is there another way/tool?

Postby SHOOTINIT » Sun Dec 17, 2017 8:05 pm

shoot it down. then push on hammer
99% of the time it's the shooter, not the gun
User avatar
SHOOTINIT
 
Posts: 2240
Joined: Thu Apr 18, 2013 10:13 am

Re: Degassing tool.. Is there another way/tool?

Postby 22synrodn » Sun Dec 17, 2017 11:01 pm

In the absence of a degas tool which is the best method, a steel rod or equivalent tool and a hammer tapping on the valve stem or hammer is way quicker than shooting it down. Much safer than unscrewing the gauge too.
Romans 8:1-11

22 Synrod Unregulated. Tuned using JSB 18.13gr:
30 Shots @ 31.02 FPE Avg., ES 1.36% (12 FPS), 1.58 FPE/CI


25 Synrod Regulated. Tuned using JSB MKIIs 33.95gr:
24 Shots @ 55.92 FPE Avg., ES 2.08% (18 FPS), 1.45 FPE/CI
User avatar
22synrodn
 
Posts: 1194
Joined: Sat Jan 10, 2015 4:33 pm

Re: Degassing tool.. Is there another way/tool?

Postby davee1 » Mon Dec 18, 2017 11:41 am

Slowly unscrewing the gauge seems like a good idea...but when I did it, the gauge popped off and hit me in the inner thigh right next to the nads!!! One inch to the left and I woulda went down like a sack. That hurt even through my thick jeans!!! The gauge face was cracked when I picked it up off the floor. The threads in the gauge adapter pulled right out and allowed that to happen...probably didnt let it leak down low enough but still....Scared the livin bejeezuz outta me too and left a mark!!!.

No disrespect intended to PB_Matrix or anyone else. Just sayin...and relaying a halfway funny story. Do it one of the other ways.
davee1
 
Posts: 65
Joined: Wed Mar 24, 2010 6:21 pm

Re: Degassing tool.. Is there another way/tool?

Postby int3man » Sun Feb 11, 2018 8:35 pm

Go with the rifle vertical barrel up, and fill and then slowly crack the bleed valve. Lets air out slowly and under control. You will have to gently open the bleed valve as the pressure gets lower. As always you are dealing with High pressure air, be careful.

Michael :- )
.25 Marauder Full W.A.R.
PRod Modified Valve, LW Barrel W.A.R. NBH
Broadening my Horizons
.22 Brocock S6 XL
.25 BSA Scorpion Huma REG
.25 Air Arms Extra FAC
.22 Marauder Regulated LW Barrel Rapid 70 Bull Stolen
W.A.R. .30 FLEX DA BOMB!! Stolen
int3man
 
Posts: 473
Joined: Fri Jan 17, 2014 10:37 pm


Return to .25 Cal Marauders

Who is online

Users browsing this forum: No registered users and 1 guest